ATS 2E

ATS 2E

Enhanced Audio Test Set

Contact Electrodata at 1-800-441-6336

The ATS 2E is a full-featured audio test set in a portable, hand-held unit. The set facilitates the installation and maintenance of leased or dial-up circuits and equipment connected to the Public Switched Telephone Network (PSTN). Designed to comply with CCITT recommendations, the ATS 2E performs all basic analog transmission measurements plus Signal-to-Noise (S/N) ratio, background noise and impulse noise tests. Noise filters provide CCITT psophometric weighting. The ATS 2E has manual and auto-dial facilities (DTMF/MF/Pulse), "line hold", integral speaker and microphone. It can also function as a telephone handset on 2- and 4-wire circuits, with dial, hold, talk and listen capabilities.

  • Menu driven
  • Impulse Noise and Signal-to-Noise tests
  • DTMF, MF or pulse dialing
  • Complies with CCITT recommendations
 

 


Specifications for the ATS 2E

SEND MODES

QUIET TERMINATION Signal generator disconnected from output Output noise: Less than -80 dBm
SEND FREQUENCY
Range: 50 Hz to 5 kHz Resolution: 1 Hz Accuracy: ±0.03% Direct entry: Numeric keypad Stepping: ±1, 10 and 100 Hz Fixed frequencies: 820 Hz, 2713 Hz and programmable auxiliary tone Slope tones: 304 Hz, 820 Hz, 2004 Hz and 3004 Hz, 5 seconds per tone Auto step: Programmable start, stop, step size and step duration Distortion: 50 Hz to 200 Hz less than -45 dB 200 Hz to 5 kHz less than -50 dB SF skip: 2130 Hz to 2430 Hz
SEND LEVEL
Range: ±10 dBm to -50 dBm Resolution: 0.1 dB
ACCURACY 50 Hz to 200 Hz: ±0.5 dB 200 Hz to 2 kHz: ±0.2 dB 820 Hz: ±0.1 dB from 0 to -19 dBm Direct entry: Numeric keypad Stepping: ±0.1 and 1 dB
FLATNESS
50 Hz to 200 Hz: ±0.5 dB 200 Hz to k5kHz: ±0.2 dB

MEASURE MODES

LEVEL/FREQUENCY Level Range: +10 dBm to -65 dBm Resolution: 0.1 dB
ACCURACY
50 Hz to 200 Hz: ±0.5 dB 200 Hz to 5 kHz: ±0.2 dB 820 Hz: ±0.1 dB from 0 to -19 dBm Detector: Averaging Display modes: Absolute or relative with respect to input level Frequency range: 20 Hz to 10 kHz Resolution: 1 Hz Accuracy: ±1 Hz
BACKGROUND NOISE
Range: 9 dBm to -80 dBm Resolution: 1 dB
ACCURACY
9 dBm to -70 dBm: ±1 dB -70 dBm to -80 dBm: ±2 dB Filters: Psophometric, 3 kHz flat, P-Notch Detector: True RMS Display Modes: Absolute or relative with respect to input level Notch filter: 800 to 860 Hz greater than 50 dB rejection Loss of tone: Less than -40 dBm
SIGNAL TO NOISE
Signal range: +10 dBm to -40 dBm Noise range: 0 dBm to -80 dBm Ratio range: 10 to 50 dB Resolution: 1 dB Accuracy: ±1 dB Detector: Average for level and true RMS for noise Display modes: Absolute or relative with respect to current measurement Notch filter: 800 to 860 Hz greater than 50 dB rejection Loss of tone: Less than -40 dBm
IMPULSE NOISE
Threshold range: 10 dBm to -60 dBm Resolution: 1 dB Accuracy: ±1 dB Count rate: 8 per second Count timer: 1 to 99 minutes or continuous Count range: 0 to 9999 Filters: Psophometric, 3 kHz flat, P-Notch Notch filter: 800 to 860 Hz greater than 50 dB rejection Loss of tone: Less than -40 dBm Loss of tone counter: 0 to 9999

DIAL MODES

MANUAL DIAL Dial method: DTMF, MF or pulse DTMF signals: Full supervisory tone set, including A, B, C and D Redial: Up to last 16 digits
AUTODIAL
Memory: 10 locations, each capable of holding up 16 digits Dial Method: DTMF, MF or pulse DTMF signals: Full supervisory tone set, including A, B, C and D

GENERAL

INPUT/OUTPUT Line: 2-wire or 4-wire Connectors: RJIIC modular jack and dual miniature phone jack (0.173" diameter on 0.312" centers, mates with ADC PJ777 or Switchcraft TT253) DC blocking: 150 volts Normal/Reverse switch: Reverse send and receive Hold circuit: Electronic, 24 ma. Impedance: 600 or 900 ohms Termination: Bridge or terminate Bridging loss: Less than 0.2 dB Return loss: Greater than 30 dB Longitudinal balance: Greater than 80 dB at 60 Hz Greater than 70 dB at 540 Hz Greater than 60 dB at 4 kHz Decreasing 6 dB per octave above 4 Hz
POWER Batteries: Rechargeable nickel cadmium Battery life: 6 hour minimum per charge, one-half hour minimum after battery low indication Recharge time: 4 hours maximum, with unit turned off AC operation: 115/230 vac, 50/60 Hz Auto shut-off: 15 minutes after last key depression
PHYSICAL
Push-to-talk: Built-in condenser microphone Monitor: Adjustable volume, switchable between send and receive Display: 2 line by 16 character, LCD
DISPLAY UPDATE Normal: 5 times per second Damped: 2 times per second Size: 254mm x 102mm x 67mm (10"L x 4"W x 2.625"H) Weight: 1 Kgram (2.25 lbs) Operating temperature: 0ºC to 50ºC Storage temperature: -20ºC to 90ºC Humidity: 10% to 90% relative humidity noncondensing Specifications subject to change without notice.
 

Electrodata Inc., P.O. Box 31780, Independence, OH 44131-0780
E-Mail: sales@electrodata.com Phone: (216)663-3333 or (800)441-6336 Fax: (440)374-4994